SKU: TECH3295
Current Sensor Module ACS712 20A Range can sense upto 20A of current flow. Sensing and controlling the current flow is a fundamental requirement in wide variety of applications, which includes over-current protection circuits, battery chargers, switching mode power supplies, digital watt meter..
₹115.00
Ex Tax:₹97.46
SKU: TECH1145
Current Sensor Module ACS712 30A consists of a precise, low-offset, linear Hall circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field which the Hall IC converts into a proportional voltage.Sen..
₹145.00
Ex Tax:₹122.88
SKU: TECH1455
Current Sensor Module ACS712 5A provides economical and precise solutions for AC or DC current sensing in industrial, Commercial and communications systems. The maximum AC or DC that can be detected can reach 5A, and the present current signal can be read via analog I / O port of Arduino. The d..
₹100.00
Ex Tax:₹84.75
SKU: TECH3255
Vibration Sensor Module Normally Open Type is based on the vibration sensor SW-420 and Comparator LM393 to detect if there is any vibration that beyond the threshold. The threshold can be adjusted by the on-board potentiometer. When this no vibration, this module output logic LOW the signal indicate..
₹40.00
Ex Tax:₹33.90
SKU: TECH1059
SCT-013-000 100A Non-invasive AC current sensor Split Core Type is a current transformer which can be used to measure AC current up to 100 amperes. It has no internal burden resistor, but a transient voltage suppressor limits the output voltage in the event of accidental disconnection from the burde..
₹375.00
Ex Tax:₹317.80
SKU: TECH7487
SCT-013-000 30A Non-invasive AC current clamp sensor Split Core Type is a Non-Invasive AC current sensor i.e. it is a current transformer that can be used to measure AC current up to 100 amperes.This non-invasive current sensor clamped around the supply line can measure a load up to 30 Amps, and all..
₹375.00
Ex Tax:₹317.80
SKU: TECH1436
Tap Sensor Module For Arduino, also called spring switch or shock knock sensor, is an electronic switch which induces shock force and transfers the result to a circuit device thus triggering it to work. It contains the following parts: conductive vibration spring, switch body, trigger pin, and packa..
₹59.00
Ex Tax:₹50.00
SKU: TECH1410
Voltage Sensor Module 25V is a simple but very useful module which uses a potential divider to reduce any input voltage by a factor of 5. This allows you to use the analogue input of a microcontroller to monitor voltages much higher than it capable of sensing. For example with a 0-5V analogue input ..
₹22.00
Ex Tax:₹18.64
SKU: TECH3299
5A range of single-phase ac current sensor module can measure AC currents less than 5A, the corresponding analog output 5A/5mA.It has Onboard sampling resistor and precision microcurrent transformer do accurate sampling for the signal and appropriate compensation, and other functions. The module can..
₹115.00
Ex Tax:₹97.46
SKU: TECH2192
This 801S Vibration Shock Sensor Module changes its resistance level once vibration is detected. It can turn into a switch if the vibration is high. According to the datasheet, it is gold-plated and can withstand 60 million shocks. This module is connected in a voltage divider which can be measured ..
₹210.00
Ex Tax:₹177.97
SKU: TECH2154
Vibration Sensor Switch Module SW-420 is based on the vibration sensor SW-420 and Comparator LM393 to detect if there is any vibration that beyond the threshold. The threshold can adjust using an onboard potentiometer. When this no vibration, this module output logic LOW the signal indicates LED lig..
₹39.00
Ex Tax:₹33.05
SKU: TECH1289
The WCS1700 current sensor provides economical and precise solutions for both DC and AC current sensing in industrial, commercial, and communications systems. The unique package provides easy implementation without breaking the original system and makes current sensing possible. Typical applic..
₹720.00
Ex Tax:₹610.17