5V-12V DC Brushless Motor Driver Board Controller for Hard Drive Motor 1.8A Max can drive hard disk brushless motors ,CD-ROM brushless motor and so on the micro 3-wire or 4-wire without hall brushless motor. It also have reverse voltage protection , Overcurrent protection , Phase inversion control, ..
A3967 Easy Driver Shield Stepper Motor Driver Module is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the Easy Driver). Easy Driver requires a 7V to 30V supply to power the motor and can pow..
Aluminum Steering Servo Horn Arm for Futaba 25T is adjustable RC rocker for RC planes servo motors. Aluminum Hole centers at 20 and 24mm from the servo output 25T spine for RC Plane. It includes two steel bolt to secure the split clamp onto servo output.It has an aluminum body and is perfect for the..
Cytron 10A Dual Channel Enhanced DC Motor Driver 30A Peak MDD10A is the dual-channel version of MD10C which is designed to drive 2 brushed DC motors with high current up to 10A continuously. Like MD10C, MDD10A also supports locked-antiphase and sign-magnitude PWM signal. It uses full solid state com..
Cytron 13A Enhanced DC Motor Driver 30A Peak 10 Seconds MD10C is a newer version of the MD10B(2008) which is designed to drive high current brushed DC motor up to 13Amps continuously. It offers several enhancements over the MD10B such as support for both locked-antiphase and sign-magnitude PWM..
The MD20A enables bidirectional control of one high-power brushed DC motor from 6V to 30V. With discrete NMOS H-Bridge design, this motor driver is able to support 20Amp continuously without any heatsink.The onboard test buttons and motor output LEDs allow functional test of the motor driver in a qu..
This is Cytron 30Amp DC Motor Driver Peak 80Amp MD30C R2. It is the successor of MD30B which is designed to drive medium to high power brushed DC motor with output current up to 80A peak (1 second) and 30A continuously. Full NMOS(solid state) design not only provides faster switching time, it is als..
Cytron SmartDrive MDDS30A 30Amp Dual DC Motor Driver (Peak 80Amp) is SmartDriveDuo-30, with the ease of accepting the RC (Radio Control) signal to drive two DC brushed motors in independent or mix mode, it is perfect for combat robots. Not to forget it supports up to 80Amps of peak current (1 second..
Cytron SmartDrive MDS40B 40Amp Enhanced DC Motor Driver (Peak 80Amp) is enhanced version of the MDS40A, it is designed to drive brushed DC motor, ranging from medium to high power motor with current capacity up to 80A peak and 40A continuously. The MOSFETs are switched at 16 KHz to ensure quie..
DRV8825 Stepper Motor Driver with Aluminum Heat Sink is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up ..
The Dual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A) is essentially a ramped up version of our Ardumoto motor driver shield. For this Monster Moto Shield, It is replaced the L298 H-bridge with a pair of VNH3ASP30 full-bridge motor drivers. VNH3ASP30 is the updated version of VNH2S..
IRF520 MOSFET Driver Module is easy hookup to your Arduino or another 3-5v micro-controller. Pulse current through a PWM pin, and use this to control a pump, LED, or other DC device at up to 24v, and ~5A. Its main purpose of this IRF520 MOSFET Driver Module is to provide a low-cost way to drive a DC..