Your Cart

DC Geared Motor Drivers

5V-12V DC Brushless Motor Driver Board Controller for Hard Drive Motor 1.8A Max can drive hard disk brushless motors ,CD-ROM brushless motor and so on the micro 3-wire or 4-wire without hall brushless motor. It also have reverse voltage protection , Overcurrent protection , Phase inversion control, ..
Ex Tax:₹800.85
The Dual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A) is essentially a ramped up version of our Ardumoto motor driver shield. For this Monster Moto Shield, It is replaced the L298 H-bridge with a pair of VNH3ASP30 full-bridge motor drivers. VNH3ASP30 is the updated version of VNH2S..
Ex Tax:₹588.98
IRF520 MOSFET Driver Module is easy hookup to your Arduino or another 3-5v micro-controller. Pulse current through a PWM pin, and use this to control a pump, LED, or other DC device at up to 24v, and ~5A. Its main purpose of this IRF520 MOSFET Driver Module is to provide a low-cost way to drive a DC..
Ex Tax:₹30.51
L293D Motor Driver Module is a medium power motor driver perfect for driving DC Motors and Stepper Motors. It uses the popular L293 motor driver IC. It can drive 4 DC motors on and off, or drive 2 DC motors with directional and speed control. The driver greatly simplifies and increases the ease with..
Ex Tax:₹59.32
This L293D Motor Driver Shield for Arduino is probably one of the most versatile on the market and features 2 servo and 4 motor connectors for DC or stepper motors. That makes it a great shield for any robotic project. This Arduino compatible motor Driver shield is a full-featured product that it ca..
Ex Tax:₹139.83
L298 2A Dual Motor Driver Module with PWM Control is a high power motor driver perfect for driving DC Motors and Stepper Motors. It uses the popular L298N motor driver IC and has on board 5V regulator which it can supply to an external circuit. It can control up to 4 DC motors, or 2 DC motors with d..
Ex Tax:₹110.17
Monster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A) has a single NH3SP30 chip which enables it to drive one DC motor. It has an extremely high current capacity of 14A per channel (peak of 30A for few seconds). The thermal heating is minimal uptill 4 to 5 amps. However it would need thermal diss..
Ex Tax:₹761.86
The TB6612FNG Ultra Small Dual DC Motor Driver Module can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes: CW, CCW, short-brake and stop. The two motor outputs (A and B) can be separ..
Ex Tax:₹296.61
5-36v Switch Drive High-Power MOSFET Trigger Module is high power MOS trigger switch driver module and control board with a field-effect tube to adjust the electronic switch. It adopts imported double MOS parallel active output to show lower internal resistance, greater electric current, and power.B..
Ex Tax:₹42.37
7V-12V DC Brushless Motor Driver Controller Board For Hard Drive Motor 3/4 Wire is a Brushless Motor Driver Controller Board For Hard Drive Motor. The driver board has voltage reverse connection protection, over-current protection, short circuit protection, simple wiring, and worry-free use. The har..
Ex Tax:₹572.03
This HG7881 4-Channel DC 2.4-10V Motor Driver Broad comes with its own four L9110S chip. It can drive 4 DC or Can drive two 4-wire 2-phase stepping motor.Features:Perfect for driving DIY smart car robot motor.You can drive 4 DC motors or two 4-wire 2-phase stepping motor.Suitable Motor range: b..
Ex Tax:₹237.29
L293D Motor Driver module is compatible with ESP12E Dev Kit and NodeMCU. This shield board is driven by the power full-bridge chip L293DD which can directly drive 2-channels DC motors or one-channel stepper motor.In this motor shield board, the IO port of ESP-12E Dev Kit is used as the control port...
Ex Tax:₹105.93
Showing 1 to 12 of 15 (2 Pages)
We use cookies and other similar technologies to improve your browsing experience and the functionality of our site as per our Privacy Policy.