Your Cart

3D Printer Parts

100K Ohm NTC Thermistors with 1m cable for 3D Printer is a temperature sensor in which the thermistor chip is welded with leads by alloy soldering process, then partially treated by glass sealing. The element has a bead form with good stability, small size and rapid response.In most RepRaps, a therm..
Ex Tax:₹46.61
10mm Kapton Tape for 3D Printer 30 Meter Length is having 12mm width and highly used to increase the adhesion of the print materials covering the heating surface. High quality Kapton Tape can be use on the build plate of your Reprap Prusa Mendel or other 3D printer. Kapton Polymide film with silicon..
Ex Tax:₹148.31
128x64 Graphic LCD Smart Controller Display for RAMPS 1.4 3D Printer contains an SD-Card reader, a rotary encoder, and a 128x64 LCD display. You can easily connect it to your Ramps board using the "smart adapter". After connecting this panel to your Ramps you don't need your pc anymore, the Smart Co..
Ex Tax:₹855.93
12V 40W Ceramic Cartridge Heater increases the reliability of your extruder with this heater cartridge. Also it heats up faster. It fits nicely in our extruders, so it's an easy replacement.This Cartridge Heater Wire consists of a cylindrical stainless steel tube and thus provides high corrosion pre..
Ex Tax:₹67.80
24V 40W Ceramic Cartridge Heater is a powerful heater replacing fragile and poorly tolerance enamel resistors and switch to a purpose made high power ceramic heater cartridge. 24V 40W Cartridge Heater Wire consists of a cylindrical stainless steel tube and thus provides high corrosion prevention. Th..
Ex Tax:₹72.03
3D Printer Controller Board RAMPS 1.4 Arduino Mega Shield is an all-in-one design to fit the necessary components for a 3D printer into one plug in shield for an Arduino MEGA. The plug in shield design includes plug in stepper drivers and extruder control electronics sockets for easy service, part r..
Ex Tax:₹275.42
3D Printer MK8 Extruder Gear / Drive Gear / Extrusion Wheel 26 Teeth 11x11mm is suitable for 1.75 mm. filament. This extruder gear are widely used in desktop FDM 3D printers.Specification: Inner diameter : 5 mm Gear Toothed Length : 7mm Outer diameter : 11mm Size(L x W) : 11mm x 11mm Number of..
Ex Tax:₹33.90
A4988 Stepper Motor Driver Module with Heatsink is a breakout board microstepping driver with translator and overcurrent protection. This stepper motor driver controls one bipolar stepper motor at up to 2 A output current per coil i.e., in full-, half-, quarter-, eighth-, and sixteenth-step modes, w..
Ex Tax:₹72.03
DRV8825 Stepper Motor Driver with Aluminum Heat Sink is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up ..
Ex Tax:₹190.68
The E3D-v6 has been redesigned from the ground up. E3D has invested a lot of time and used all of their experience to design E3D's latest and greatest Hot End. This E3D v6 J-Head Hotend Extruder 1.75mm Filament 0.2mm Nozzle w/Fan Duct contains the same signature high-temperature performance for..
Ex Tax:₹500
12V DC 5015 Vortex Turbo Cooling Fan for 3D Printer is high temperature resistant and extremely durable. Excellent for cooling heat sinks on hot ends, prints, or other cooling needs.It is made of high quality PBT+30% glass line +VO and Bearing with high precision make it provide long life and low no..
Ex Tax:₹75.42
Modify your 3D printer to print fine details or large parts with M6 Thread Brass Nozzle V5 V6 UM Compatible – 3mm x 0.3mm. These nozzles are fully integrated into the ecosystem of 3D printer parts and are compatible with V6, Lite6, and Titan Aero. Compatible with Prusa 3D printers.Compatible wi..
Ex Tax:₹29.66
Showing 1 to 12 of 48 (4 Pages)
We use cookies and other similar technologies to improve your browsing experience and the functionality of our site as per our Privacy Policy.